Шаги для Замена a Низкий Мощность Зеркало с a Высокая Мощность Зеркало В A Микроскоп
Как есть хорошо известно, во время the use of a микроскоп, the sample to be magnified and наблюдаемый is обычно первый наблюдаемый с a low-power lens, then moved to the center of the field of view, and наконец замененный с a high-power lens for observation. Поэтому, there is a transition между low-power and high-power while use, which is commonly known as low-power lens for field of view and high-power lens for observing the sample. This is also the most basic common knowledge used in microscopes, but the methods used are different, The follow will provide a detailed introduction to the usage methods between low-power mirrors, high-power mirrors, and oil mirrors.
Steps for using low-power mirrors
Когда наблюдение любой образец, it is необходимый к первый использование a маломощный микроскоп потому что его поле из вид is large, making it easy to detect the target and determine the area to be observation.
(1) Зеркало поиск и размещение
Микроскопы есть высокоточные оптические экспериментальные приборы это есть обычно упакованные и помещенные в коробки когда не в использование. они есть затем взято и открыто когда в использование. Когда вынимает в зеркало, вынимает вправо рука крепко хватает зеркало рука и влево рука удерживает зеркало база держать зеркало тело вертикальный к предотвратить зеркало и окуляр от скольжение и выбрасывание выбрасывание наружу. Аккуратно место Микроскоп на Экспериментальный Стол, обычно на В Влево Сторона, 3-4 сантиметры от В Стол Край, с Зеркало Рука Обращение КляК На Грудь Для Простой Наблюдение.
(2) Очистка
(3) прицеливание шаги
Поднять объектив трубку к а расстояние из 7b{0}}} сантиметры от the stage, поворот объектив объектив объектив конвертер, и поворот the low увеличение объектив навстречу the stage, выравнивание it with the central light hole. Во время вращения process, it should be slow. When you hear a click sound, open the upator, raise the concentrator, and turn the reflector towards the light source. Наблюдать с ваш влево глаз на в окуляр (делать не закрыть ваш вправо глаз плотно), while while the direction of the reflector until the light in your field of view is evenly brightly.
(4) Placing slide specimens
Взять a стекло слайд образец и место это на сцене 2c создание обязательно это сторона с крышка стекло есть лицом вверх. В противном случае, когда наблюдение с a высокая мощность микроскоп , фокус не может быть отрегулирован , и стекло слайд образец есть склонность к повреждению. Затем использование a нарезка зажим зажим стекло слайд плотно, поворот винт из платформа сдвиг , и выравнивание область к быть наблюдение наблюдение с центр из свет отверстие.
(5) Adjusting the focal length
Rotate the coarse adjuster counterclockwise with your left hand to slowly raise the lens to a distance of about 5 millimeters from the objective lens to the specimen. Be careful not to observe on the eyepiece when raising the lens. Be sure to watch the mirror stand rise from the right side to avoid excessive rise and damage to the lens or specimen. Then, open both eyes at the same time, observe with your left eye on the eyepiece, and slowly rotate the coarse adjuster clockwise with your left hand to slowly lower the lens until a clear object appears in your field of view.
Note: If the object image is not in the center of the field of view, the slide pusher can be adjusted to center it (note that the direction of moving the slide is opposite to the direction of moving the object image in the field of view). If the brightness in the field of view is not suitable, it can be adjusted by adjusting the position of the concentrator or the size of the opening and closing aperture. If the lens table drops beyond the working distance (>5,40 мм) и нет объект есть видимый во время the adjustment of the focal length, it it указывает that the operation has failed. Следовательно, the operation should be repeated and must not be repeat
